If the scapha, or flat, of the ear protrudes past the helical curl, or shell, then the barbell shaft will place too much pressure on the scapha and will cause physical damage to the ear. This damage can be in the form of a cut created by the barbell or the ends of the barbell migrating out of the ear.
Secondly, should my Industrial bar touch my ear?
In fact, it’s best not to touch your new piercing at all. If you remove the jewelry too early, you put your piercing at risk of closing up or getting infected. Try not to poke, touch, or play with your new piercing either — it could prolong the process (and hurt).
Also question is, how do you know if your industrial piercing is rejecting?
Symptoms of piercing rejection
more of the jewelry becoming visible on the outside of the piercing. the piercing remaining sore, red, irritated, or dry after the first few days. the jewelry becoming visible under the skin. the piercing hole appearing to be getting larger.
How do I know if my ear is good for an industrial piercing?
Most people’s ears are suitable to get an industrial piercing. However some people’s ears don’t have a prominent ridge on the upper part of the ear. If your ear has a prominent ridge that runs from the upper part of the ear to about midway then you should be able to get an industrial no problem.
Are my ears too small for an industrial piercing?
The look of an industrial piercing greatly depends on the anatomy of your ear. If you have a smaller ear, you might not be able to accommodate the industrial piercing. … If you’ve had problems healing cartilage in the past, then it’s a good idea to talk to your piercer before pursuing the industrial piercing.
Does Claire’s do industrial bar piercings?
This cool industrial bar for cartilage piercings will add a pretty touch to your cool cartilage piercings. It has a delicate key design embellished with pretty clear gems.
Should I move my industrial piercing while cleaning it?
–Never spin the jewelry, move it back and forth, or move it while you’re cleaning it. The jewelry may feel tight or like it’s not moving around and that is OK. It will move around on it’s own. –In your shower, avoid any shampoo, conditioner or soap on the piercing.
Are industrial piercings worth it?
Industrial piercings look absolutely awesome, but you have to take very good care of them. Cartilage piercings generally take longer to heal, and an industrial is two piercings rather than one. Stick to what your piercer says in terms of when you can take it out, and add a couple of weeks, just to be on the safe side.
Can I sleep on my industrial piercing?
You want to avoid sleeping on an industrial piercing because it adds additional pressure on the jewelry. It will be more likely to have scarring if you sleep on it.
How bad is an industrial piercing?
Industrial piercings are moderately painful. While they tend to hurt more than standard lobe piercings, they’re still much less painful than piercings on more sensitive areas. … The initial piercing pain is a sharp pain, like a hard pinch, and you may also experience some pain as the jewelry is pushed in place.
How do you shower with an industrial piercing?
It’s perfectly safe to continue showering and washing your hair while your piercing heals. You may want to opt for a natural shampoo if the chemicals are irritating the area. Otherwise, simply take extra care to thoroughly rinse the soap and shampoo from in and around the piercing.
What piercings reject the most?
What piercings reject the most? Surface piercings have the highest rejection rate. Surface piercings such as microdermals as well as eyebrow piercings and navel piercings reject the most because they are closest to the surface of the skin.
Do industrial piercing get infected easily?
An industrial piercing can describe any two pierced holes connected by a single barbell. It usually refers to double perforation on the cartilage at the top of your ear. Cartilage piercings — particularly those high on your ear — are more prone to infection than other ear piercings.
Can I clean my industrial piercing with alcohol?
When cleaning your industrial piercing it’s important to avoid using harsh cleaners like alcohol or hydrogen peroxide. … Clean the piercing using a solution made of 1 gallon distilled water to 4 tea spoons of non-iodized sea salt. You can also use the same solution on the compress.
