The length of the barbell can range from 28-55mm in length depending on how far apart the piercing holes are located on your ear and of course by how large your ear is. The angle of the piercings and distance between the piercings will determine if a barbell industrial piercing is a good selection for you personally.
In respect to this, what sizes do industrial barbells come in?
Standard piercing sizes
Piercing | Standard Gauge | Standard Length |
---|---|---|
Industrial Barbell | 14G (16G is also commonly used) | 1 1/2″ (varies) |
Labret Lip Rings | 14G or 16G | 1/4″ , 5/16″, and 3/8″ |
Monroe Piercing | 16G | 1/4″ , 5/16″ and 3/8″ |
Nipple Piercing | 14G | 3/8″ , 1/2″, 9/16″ |
Simply so, do I have the anatomy for an industrial piercing?
Broken down to basics, an industrial piercing is two holes connected by one piece of jewelry—typically a barbell. … “Most people do not have the right anatomy to get a traditional industrial piercing,” she says.
Can you sleep on an industrial piercing?
Can I sleep on my industrial piercing? You want to avoid sleeping on an industrial piercing because it adds additional pressure on the jewelry. It will be more likely to have scarring if you sleep on it.
Are all industrial bars the same size?
The barbell piercing worn in the ear cartilage goes by a few different names : The barbell is called an industrial barbell, construction bar, or industrial project bar. Sizing of these bars varies depending on the person, because everybody’s ears are a different size.
What size is a normal industrial piercing?
The standard measure of the industrial barbell
Because every ear is different, the room between the two piercing holes differs from person to person. Therefore the standard measure of the industrial barbell has the longest length, 38 mm. That’s long enough for everyone.
What does an industrial piercing say about you?
Industrial Piercing
You tend to draw people in with your charming personality, but you only have a few very close friends. You‘re less likely to get hurt that way, because you may look all rough and tumble, but you‘re a big softy on the inside.
How bad does an industrial piercing hurt?
Industrial piercings are moderately painful. While they tend to hurt more than standard lobe piercings, they’re still much less painful than piercings on more sensitive areas. … The initial piercing pain is a sharp pain, like a hard pinch, and you may also experience some pain as the jewelry is pushed in place.
What is the smallest gauge for an industrial piercing?
Body Piercing Standard Gauges:
Piercing | Standard Gauge |
---|---|
Industrial Barbell | 14G (16G is also commonly used) |
Labret Lip Rings | 14G or 16G |
Monroe Piercing | 16G |
Nipple Piercing | 14G |
Do Industrial Bar holes close?
The industrial piercing goes through cartilage in your ear and depending on how long it has been pierced it will close eventually and faster than many other piercings because of the location.
Is 14g bigger than 16G?
14g is bigger. The lower the number, the bigger the needle or jewelry. … So buy 16g jewelry and a 14g needle, or 14g jewelry and a 12g needle. Body piercing doesn’t really use odd numbers, so the next size will always be the next even number.
Which ear is best for industrial piercing?
Most people’s ears are suitable to get an industrial piercing. However some people’s ears don’t have a prominent ridge on the upper part of the ear. If your ear has a prominent ridge that runs from the upper part of the ear to about midway then you should be able to get an industrial no problem.
Do industrial piercings get infected easily?
An industrial piercing can describe any two pierced holes connected by a single barbell. … Cartilage piercings — particularly those high on your ear — are more prone to infection than other ear piercings. That’s because these piercings are typically closer to your hair.
Are industrial piercings worth it?
It may seem like a lot, but I can promise that all of the work is absolutely worth it. I am in love with my industrial, so much so that even a year later I find myself admiring it. If you’re thinking about doing it, go for it!