Can I put a 16 gauge in a 18 gauge hole cartilage?

Yes you can, in fact that’s typically what a piercer will do, especially with cartilage piercings. They pierce with a gauge size bigger than the actual jewelry. It allows room for swelling and placing the jewelry.

>> Click to read more <<

In respect to this, what gauge should a cartilage piercing be?

Standard piercing sizes

Piercing Standard Gauge Standard Length
Cartilage Piercing 16G , 18G 3/16″ , 1/4″ and 5/16″
Eyebrow Piercing 16G (14G is also commonly used) 1/4″ , 5/16″ and 3/8″
Industrial Barbell 14G (16G is also commonly used) 1 1/2″ (varies)
Labret Lip Rings 14G or 16G 1/4″ , 5/16″, and 3/8″
Consequently, is 14G bigger than 16G? Jewelry is measured through a gauge system (see chart below). The higher the gauge number the smaller the wire is. A standard “earring” is usually 20 gauge. Jewelry gauges/sizes can vary between manufacturers.
Gauge Millimeter Inch
16g 1.2mm 3/64″
14g 1.6mm 1/16″
12g 2mm 5/64″
10g 2.4mm 3/32″

In this manner, can I put a 14G in a 16G piercing?

14g jewelry is larger than 16g jewelry, but you might be able to fit it. Yes, you can stretch you piercing to a 14g just make sure that the jewelry that you’re buying is suitable for a freshly stretching piercing. … It would just irritate the piercing even if it is fully healed.

Can I put a 20g in a 16G piercing?

yes you can. When learning about piercings sizes you will know that the bigger the number the smaller the gauge of the piercing so yes you may use an 18g. the 18g is smaller than the 16g. Just be aware though that sometimes user smaller jewelry could cause your jewelry to get accustomed to that size.

How can I widen my helix piercing?

First, take a hot shower, and massage the area. This will help the cartilage stretch easier by pulling more blood into the area! Next, once you’re out of the shower of course, take the taper and try to insert it. If it doesn’t easily go in, remove it and put the lube on the taper and on your ear!

When can I put a hoop in my Helix?

Most piercing points suggest 4 to 6 weeks for changing cartilage but it’s better to wait at least 8 to 10 weeks.

Can you put a regular earring in a helix piercing?

In some cases, you can use any type of earring for the cartilage piercing, such as hoops and posts. Yet, earrings made for cartilage are generally more comfortable. Cartilage earring types include: … Posts or studs: Posts or studs in all metal or metal with gem stones are suitable for cartilage piercings.

Can I wear a smaller gauge earring?

Yes you can. The jewellery won’t be very snug, though, and might move around a lot. Having said that, the whole will probably close up a bit around the smaller gauge jewellery so you might not be able to wear 14g there any more. … So I used this 2mm diameter needle for a piercing with a 16g jewellery.

What is the smallest gauge for belly rings?

Gauge – width of the shaft (eg. 14g)

Gauge Millimeter Inches
16g 1.2mm 3/64″
14g (standard) 1.6mm 1/16″
12g 2mm 5/64″
10g 2.4mm 3/32″

How big is a 14 gauge piercing?

1.6 millimeters

What is the smallest gauge size?

The sizes range from millimeter measurements to inch measurements. The smallest gauge, 20, measures 0.88 millimeters or 1/32 inch. The bigger the gauge, the smaller the numbers get.

How long should a helix bar be?

The bar length you need will depend on your skin thickness and piercing location, recommended lengths are usually 6mm or 8mm. For a short and snug fit, we recommend a 6mm length, if you have thicker cartilage or prefer to leave a bit of space either side then an 8mm may be better suited.

Is 18G or 20G smaller?

When choosing your items specifics from the drop down list, please note the following: 18G = 18 Gauge 20G= 20 Gauge 22G= 22 Gauge 14K= 14 Karat Solid Gold 18K= 18 Karat Solid Gold 24K= 24 Karat Solid Gold 1.5mm Gem= Gemstone measures approx 1.5 millimeters in size 2mm Gem= Gemstone measures approx 2 millimeters in size …

What size hoop should I get for my Helix?

JEWELRY TYPE

Standard Hoop Inner Diameter
Ear Cartilage (Helix, Tragus, Lobe, etc.) 5/16″ (8mm)
Conch 3/8″-1/2″ (10mm-12mm)
Nose 5/16″ (8mm)
Septum 5/16″ (8mm)

Leave a Reply